PERCORSO: >> Multiport serial boards >> pci express serial boards

CP-102UF-S-ST-T, 2 Port UPCI Fiber Board, Single-mode, ST Connector, up to 40 km, Wide Temperature

Features and Benefits

Extend serial transmission distance up to:
> 40 km with single-mode (CP-102UF-S)
> 5 km with multi-mode (CP-102UF-M)

Supports “Ring” and “Point-to-Point” transmission modes

921.6 Kbps maximum baudrate for super fast data transmission

128-byte FIFO and on-chip H/W, S/W flow control

Compatible with 3.3/5V PCI and PCI-X

Drivers provided for Windows (7 x86/x64, XP/2003/Vista/2008 x86/x64, 2000), Windows XP Embedded, Windows CE 5.0/6.0, DOS, Linux 2.4, Linux 2.6 (x86/x64), QNX 6, SCO OpenServer 5/6, and UnixWare 7

Easy maintenance with on-board LED display and management software

Immune from signal interference

Guards against electronic degradation and chemical corrosion

Wide temperature model available for -40 to 85°C environments

Overview

The CP-102UF smart Universal PCI boards are designed for industrial automation applications that require a long distance, multi-point, PC-based data acquisition solution. The boards are compatible with all popular operating systems, and each of the 2 serial ports support data rates up to 921.6 Kbps. In addition, the CP-102UF boards work with both 3.3V and 5V PCI buses, allowing them to be installed in virtually any available PC server. With a maximum data transmission distance of 40 km (with the single-mode model), the CP-102UF cards beat the 15 meter maximum for RS-232, and even the 1.2 km maximum for RS-422/485. For many industrial applications, an even bigger benefit is that optical fiber isolates the data from dangerous increases in ground potential, ground loops, and electrical EMI/RFI electromagnetic radiation.

Ring Operation

With the CP-102UF card, your PC can be included as one node of a fiber ring formed using Moxa’s own TCF-142 serial-to-fiber converter. Since each TCF-142 has two fiber ports and one serial port, PCs that are part of the ring will be able to communicate with serial devices connected to the ring. Note that the Tx port of the CP-102UF connects to a neighboring converter’s Rx port to form the ring. Once the ring has been set up, simply use the DIP switches to configure the CP-102UF to “Ring mode.” When one node transmits a signal, the signal travels around the ring until it returns back to the transmitting unit, which then blocks the signals. With the CP-102UF, you can set up fiber rings that are up to 100 km in total length.

• Hardware

Bus 32-bit Universal PCI
Number of Ports 2
Max. Number of Boards per PC 4

• Optical Fiber Interface

Mode CP-102UF-M: Multi-mode
CP-102UF-S: Single-mode
Fiber Connectors ST type
Cable Requirements CP-102UF-M: 50/125, 62.5/125, or 100/140 μm
CP-102UF-S: 8.3/125, 8.75/125, 9/125 or 10/140 μm
Transmission Distance CP-102UF-M: Up to 5 km with multi-mode fiber
CP-102UF-S: Up to 40 km with single-mode fiber
Wavelength CP-102UF-M: 820 nm
CP-102UF-S: 1310 nm
Tx Output -5 dBm
Rx Sensitivity CP-102UF-M: -20 dBm
CP-102UF-S: -24 dBm
Point-to-Point Transmission Half or full duplex
Ring Transmission Half duplex

• Performance

Baudrate 50 bps to 921.6 Kbps

• Serial Communication Parameters

Data Bits 5, 6, 7, 8
Stop Bits 1, 1.5, 2
Parity None, Even, Odd, Space, Mark
Flow Control XON/XOFF
I/O Address Assigned by BIOS
IRQ Assigned by BIOS

• Driver Support

Operating Systems Windows 2000, Windows XP/2003/Vista/2008/7 x86/x64, Windows XP Embedded, DOS, Windows CE 5.0/6.0, DOS, Linux 2.4, Linux 2.6 x86/x64, QNX 6, SCO OpenServer 5/6, UnixWare 7
Note Please refer to Moxa's website for the latest driver support information.

• Physical Characteristics

Dimensions 70 x 120 mm (2.76 x 4.72 in)

• Environmental Limits

Operating Temperature Standard Models: 0 to 55°C (32 to 131°F)
Wide Temp. Models: -40 to 85°C (-40 to 185°F)
Storage Temperature -40 to 85°C (-40 to 185°F)
Ambient Relative Humidity 5 to 95% (non-condensing)

• Standards and Certifications

EMC CE, FCC
EMI EN 55022, EN 61000-3-2, EN 61000-3-3, FCC Part 15 Subpart B Class B
EMS EN 55024, IEC 61000-4-2, IEC 61000-4-3, IEC 61000-4-4, IEC 61000-4-5, IEC 61000-4-6, IEC 61000-4-8, IEC 61000-4-11 (DIPS)
Green Product RoHS, CRoHS, WEEE

• MTBF (mean time between failures)

Time 591,349 hrs
Database Telcordia (Bellcore), GB

• Power Requirements
 

Power Consumption CP-102UF-M: 429 mA @ +5V
CP-102UF-S: 424 mA @ +5V

• Warranty

Warranty Period 5 years